/* * Copyright (C) 2018-2020 Marvell International Ltd. * * SPDX-License-Identifier: BSD-3-Clause * https://spdx.org/licenses */ #include #ifdef USE_CCI #include #endif #include #include #include #include #include #include #include #include #include #include #include #include /* Warm reset register */ #define MVEBU_WARM_RESET_REG (MVEBU_NB_REGS_BASE + 0x840) #define MVEBU_WARM_RESET_MAGIC 0x1D1E /* North Bridge GPIO1 SEL register */ #define MVEBU_NB_GPIO1_SEL_REG (MVEBU_NB_REGS_BASE + 0x830) #define MVEBU_NB_GPIO1_UART1_SEL BIT(19) #define MVEBU_NB_GPIO1_GPIO_25_26_EN BIT(17) #define MVEBU_NB_GPIO1_GPIO_19_EN BIT(14) #define MVEBU_NB_GPIO1_GPIO_18_EN BIT(13) /* CPU 1 reset register */ #define MVEBU_CPU_1_RESET_VECTOR (MVEBU_REGS_BASE + 0x14044) #define MVEBU_CPU_1_RESET_REG (MVEBU_REGS_BASE + 0xD00C) #define MVEBU_CPU_1_RESET_BIT 31 /* IRQ register */ #define MVEBU_NB_IRQ_STATUS_1_REG (MVEBU_NB_SB_IRQ_REG_BASE) #define MVEBU_NB_IRQ_STATUS_2_REG (MVEBU_NB_SB_IRQ_REG_BASE + \ 0x10) #define MVEBU_NB_IRQ_MASK_2_REG (MVEBU_NB_SB_IRQ_REG_BASE + \ 0x18) #define MVEBU_SB_IRQ_STATUS_1_REG (MVEBU_NB_SB_IRQ_REG_BASE + \ 0x40) #define MVEBU_SB_IRQ_STATUS_2_REG (MVEBU_NB_SB_IRQ_REG_BASE + \ 0x50) #define MVEBU_NB_GPIO_IRQ_MASK_1_REG (MVEBU_NB_SB_IRQ_REG_BASE + \ 0xC8) #define MVEBU_NB_GPIO_IRQ_MASK_2_REG (MVEBU_NB_SB_IRQ_REG_BASE + \ 0xD8) #define MVEBU_SB_GPIO_IRQ_MASK_REG (MVEBU_NB_SB_IRQ_REG_BASE + \ 0xE8) #define MVEBU_NB_GPIO_IRQ_EN_LOW_REG (MVEBU_NB_GPIO_IRQ_REG_BASE) #define MVEBU_NB_GPIO_IRQ_EN_HIGH_REG (MVEBU_NB_GPIO_IRQ_REG_BASE + \ 0x04) #define MVEBU_NB_GPIO_IRQ_STATUS_LOW_REG (MVEBU_NB_GPIO_IRQ_REG_BASE + \ 0x10) #define MVEBU_NB_GPIO_IRQ_STATUS_HIGH_REG (MVEBU_NB_GPIO_IRQ_REG_BASE + \ 0x14) #define MVEBU_NB_GPIO_IRQ_WK_LOW_REG (MVEBU_NB_GPIO_IRQ_REG_BASE + \ 0x18) #define MVEBU_NB_GPIO_IRQ_WK_HIGH_REG (MVEBU_NB_GPIO_IRQ_REG_BASE + \ 0x1C) #define MVEBU_SB_GPIO_IRQ_EN_REG (MVEBU_SB_GPIO_IRQ_REG_BASE) #define MVEBU_SB_GPIO_IRQ_STATUS_REG (MVEBU_SB_GPIO_IRQ_REG_BASE + \ 0x10) #define MVEBU_SB_GPIO_IRQ_WK_REG (MVEBU_SB_GPIO_IRQ_REG_BASE + \ 0x18) /* PMU registers */ #define MVEBU_PM_NB_PWR_CTRL_REG (MVEBU_PMSU_REG_BASE) #define MVEBU_PM_PWR_DN_CNT_SEL BIT(28) #define MVEBU_PM_SB_PWR_DWN BIT(4) #define MVEBU_PM_INTERFACE_IDLE BIT(0) #define MVEBU_PM_NB_CPU_PWR_CTRL_REG (MVEBU_PMSU_REG_BASE + 0x4) #define MVEBU_PM_L2_FLUSH_EN BIT(22) #define MVEBU_PM_NB_PWR_OPTION_REG (MVEBU_PMSU_REG_BASE + 0x8) #define MVEBU_PM_DDR_SR_EN BIT(29) #define MVEBU_PM_DDR_CLK_DIS_EN BIT(28) #define MVEBU_PM_WARM_RESET_EN BIT(27) #define MVEBU_PM_DDRPHY_PWRDWN_EN BIT(23) #define MVEBU_PM_DDRPHY_PAD_PWRDWN_EN BIT(22) #define MVEBU_PM_OSC_OFF_EN BIT(21) #define MVEBU_PM_TBG_OFF_EN BIT(20) #define MVEBU_PM_CPU_VDDV_OFF_EN BIT(19) #define MVEBU_PM_AVS_DISABLE_MODE BIT(14) #define MVEBU_PM_AVS_VDD2_MODE BIT(13) #define MVEBU_PM_AVS_HOLD_MODE BIT(12) #define MVEBU_PM_L2_SRAM_LKG_PD_EN BIT(8) #define MVEBU_PM_EIP_SRAM_LKG_PD_EN BIT(7) #define MVEBU_PM_DDRMC_SRAM_LKG_PD_EN BIT(6) #define MVEBU_PM_MCI_SRAM_LKG_PD_EN BIT(5) #define MVEBU_PM_MMC_SRAM_LKG_PD_EN BIT(4) #define MVEBU_PM_SATA_SRAM_LKG_PD_EN BIT(3) #define MVEBU_PM_DMA_SRAM_LKG_PD_EN BIT(2) #define MVEBU_PM_SEC_SRAM_LKG_PD_EN BIT(1) #define MVEBU_PM_CPU_SRAM_LKG_PD_EN BIT(0) #define MVEBU_PM_NB_SRAM_LKG_PD_EN (MVEBU_PM_L2_SRAM_LKG_PD_EN |\ MVEBU_PM_EIP_SRAM_LKG_PD_EN | MVEBU_PM_DDRMC_SRAM_LKG_PD_EN |\ MVEBU_PM_MCI_SRAM_LKG_PD_EN | MVEBU_PM_MMC_SRAM_LKG_PD_EN |\ MVEBU_PM_SATA_SRAM_LKG_PD_EN | MVEBU_PM_DMA_SRAM_LKG_PD_EN |\ MVEBU_PM_SEC_SRAM_LKG_PD_EN | MVEBU_PM_CPU_SRAM_LKG_PD_EN) #define MVEBU_PM_NB_PWR_DEBUG_REG (MVEBU_PMSU_REG_BASE + 0xC) #define MVEBU_PM_NB_FORCE_CLK_ON BIT(30) #define MVEBU_PM_IGNORE_CM3_SLEEP BIT(21) #define MVEBU_PM_IGNORE_CM3_DEEP BIT(20) #define MVEBU_PM_NB_WAKE_UP_EN_REG (MVEBU_PMSU_REG_BASE + 0x2C) #define MVEBU_PM_SB_WKP_NB_EN BIT(31) #define MVEBU_PM_NB_GPIO_WKP_EN BIT(27) #define MVEBU_PM_SOC_TIMER_WKP_EN BIT(26) #define MVEBU_PM_UART_WKP_EN BIT(25) #define MVEBU_PM_UART2_WKP_EN BIT(19) #define MVEBU_PM_CPU_TIMER_WKP_EN BIT(17) #define MVEBU_PM_NB_WKP_EN BIT(16) #define MVEBU_PM_CORE1_FIQ_IRQ_WKP_EN BIT(13) #define MVEBU_PM_CORE0_FIQ_IRQ_WKP_EN BIT(12) #define MVEBU_PM_CPU_0_PWR_CTRL_REG (MVEBU_PMSU_REG_BASE + 0x34) #define MVEBU_PM_CPU_1_PWR_CTRL_REG (MVEBU_PMSU_REG_BASE + 0x38) #define MVEBU_PM_CORE_SOC_PD BIT(2) #define MVEBU_PM_CORE_PROC_PD BIT(1) #define MVEBU_PM_CORE_PD BIT(0) #define MVEBU_PM_CORE_1_RETURN_ADDR_REG (MVEBU_PMSU_REG_BASE + 0x44) #define MVEBU_PM_CPU_VDD_OFF_INFO_1_REG (MVEBU_PMSU_REG_BASE + 0x48) #define MVEBU_PM_CPU_VDD_OFF_INFO_2_REG (MVEBU_PMSU_REG_BASE + 0x4C) #define MVEBU_PM_LOW_POWER_STATE BIT(0) #define MVEBU_PM_CPU_WAKE_UP_CONF_REG (MVEBU_PMSU_REG_BASE + 0x54) #define MVEBU_PM_CORE1_WAKEUP BIT(13) #define MVEBU_PM_CORE0_WAKEUP BIT(12) #define MVEBU_PM_WAIT_DDR_RDY_VALUE (0x15) #define MVEBU_PM_SB_CPU_PWR_CTRL_REG (MVEBU_SB_WAKEUP_REG_BASE) #define MVEBU_PM_SB_PM_START BIT(0) #define MVEBU_PM_SB_PWR_OPTION_REG (MVEBU_SB_WAKEUP_REG_BASE + 0x4) #define MVEBU_PM_SDIO_PHY_PDWN_EN BIT(17) #define MVEBU_PM_SB_VDDV_OFF_EN BIT(16) #define MVEBU_PM_EBM_SRAM_LKG_PD_EN BIT(11) #define MVEBU_PM_PCIE_SRAM_LKG_PD_EN BIT(10) #define MVEBU_PM_GBE1_TX_SRAM_LKG_PD_EN BIT(9) #define MVEBU_PM_GBE1_RX_SRAM_LKG_PD_EN BIT(8) #define MVEBU_PM_GBE1_MIB_SRAM_LKG_PD_EN BIT(7) #define MVEBU_PM_GBE0_TX_SRAM_LKG_PD_EN BIT(6) #define MVEBU_PM_GBE0_RX_SRAM_LKG_PD_EN BIT(5) #define MVEBU_PM_GBE0_MIB_SRAM_LKG_PD_EN BIT(4) #define MVEBU_PM_SDIO_SRAM_LKG_PD_EN BIT(3) #define MVEBU_PM_USB2_SRAM_LKG_PD_EN BIT(2) #define MVEBU_PM_USB3_H_SRAM_LKG_PD_EN BIT(1) #define MVEBU_PM_SB_SRAM_LKG_PD_EN (MVEBU_PM_EBM_SRAM_LKG_PD_EN |\ MVEBU_PM_PCIE_SRAM_LKG_PD_EN | MVEBU_PM_GBE1_TX_SRAM_LKG_PD_EN |\ MVEBU_PM_GBE1_RX_SRAM_LKG_PD_EN | MVEBU_PM_GBE1_MIB_SRAM_LKG_PD_EN |\ MVEBU_PM_GBE0_TX_SRAM_LKG_PD_EN | MVEBU_PM_GBE0_RX_SRAM_LKG_PD_EN |\ MVEBU_PM_GBE0_MIB_SRAM_LKG_PD_EN | MVEBU_PM_SDIO_SRAM_LKG_PD_EN |\ MVEBU_PM_USB2_SRAM_LKG_PD_EN | MVEBU_PM_USB3_H_SRAM_LKG_PD_EN) #define MVEBU_PM_SB_WK_EN_REG (MVEBU_SB_WAKEUP_REG_BASE + 0x10) #define MVEBU_PM_SB_GPIO_WKP_EN BIT(24) #define MVEBU_PM_SB_WKP_EN BIT(20) /* DRAM registers */ #define MVEBU_DRAM_STATS_CH0_REG (MVEBU_DRAM_REG_BASE + 0x4) #define MVEBU_DRAM_WCP_EMPTY BIT(19) #define MVEBU_DRAM_CMD_0_REG (MVEBU_DRAM_REG_BASE + 0x20) #define MVEBU_DRAM_CH0_CMD0 BIT(28) #define MVEBU_DRAM_CS_CMD0 BIT(24) #define MVEBU_DRAM_WCB_DRAIN_REQ BIT(1) #define MVEBU_DRAM_PWR_CTRL_REG (MVEBU_DRAM_REG_BASE + 0x54) #define MVEBU_DRAM_PHY_CLK_GATING_EN BIT(1) #define MVEBU_DRAM_PHY_AUTO_AC_OFF_EN BIT(0) /* AVS registers */ #define MVEBU_AVS_CTRL_2_REG (MVEBU_AVS_REG_BASE + 0x8) #define MVEBU_LOW_VDD_MODE_EN BIT(6) /* Clock registers */ #define MVEBU_NB_CLOCK_SEL_REG (MVEBU_NB_REGS_BASE + 0x10) #define MVEBU_A53_CPU_CLK_SEL BIT(15) /* North Bridge Step-Down Registers */ #define MVEBU_NB_STEP_DOWN_INT_EN_REG MVEBU_NB_STEP_DOWN_REG_BASE #define MVEBU_NB_GPIO_INT_WAKE_WCPU_CLK BIT(8) #define MVEBU_NB_GPIO_18 18 #define MVEBU_NB_GPIO_19 19 #define MVEBU_NB_GPIO_25 25 #define MVEBU_NB_GPIO_26 26 typedef int (*wake_up_src_func)(union pm_wake_up_src_data *); struct wake_up_src_func_map { enum pm_wake_up_src_type type; wake_up_src_func func; }; void marvell_psci_arch_init(int die_index) { } void a3700_pm_ack_irq(void) { uint32_t reg; reg = mmio_read_32(MVEBU_NB_IRQ_STATUS_1_REG); if (reg) mmio_write_32(MVEBU_NB_IRQ_STATUS_1_REG, reg); reg = mmio_read_32(MVEBU_NB_IRQ_STATUS_2_REG); if (reg) mmio_write_32(MVEBU_NB_IRQ_STATUS_2_REG, reg); reg = mmio_read_32(MVEBU_SB_IRQ_STATUS_1_REG); if (reg) mmio_write_32(MVEBU_SB_IRQ_STATUS_1_REG, reg); reg = mmio_read_32(MVEBU_SB_IRQ_STATUS_2_REG); if (reg) mmio_write_32(MVEBU_SB_IRQ_STATUS_2_REG, reg); reg = mmio_read_32(MVEBU_NB_GPIO_IRQ_STATUS_LOW_REG); if (reg) mmio_write_32(MVEBU_NB_GPIO_IRQ_STATUS_LOW_REG, reg); reg = mmio_read_32(MVEBU_NB_GPIO_IRQ_STATUS_HIGH_REG); if (reg) mmio_write_32(MVEBU_NB_GPIO_IRQ_STATUS_HIGH_REG, reg); reg = mmio_read_32(MVEBU_SB_GPIO_IRQ_STATUS_REG); if (reg) mmio_write_32(MVEBU_SB_GPIO_IRQ_STATUS_REG, reg); } /***************************************************************************** * A3700 handler called to check the validity of the power state * parameter. ***************************************************************************** */ int a3700_validate_power_state(unsigned int power_state, psci_power_state_t *req_state) { ERROR("%s needs to be implemented\n", __func__); panic(); } /***************************************************************************** * A3700 handler called when a CPU is about to enter standby. ***************************************************************************** */ void a3700_cpu_standby(plat_local_state_t cpu_state) { ERROR("%s needs to be implemented\n", __func__); panic(); } /***************************************************************************** * A3700 handler called when a power domain is about to be turned on. The * mpidr determines the CPU to be turned on. ***************************************************************************** */ int a3700_pwr_domain_on(u_register_t mpidr) { /* Set barrier */ dsbsy(); /* Set the cpu start address to BL1 entry point */ mmio_write_32(MVEBU_CPU_1_RESET_VECTOR, PLAT_MARVELL_CPU_ENTRY_ADDR >> 2); /* Get the cpu out of reset */ mmio_clrbits_32(MVEBU_CPU_1_RESET_REG, BIT(MVEBU_CPU_1_RESET_BIT)); mmio_setbits_32(MVEBU_CPU_1_RESET_REG, BIT(MVEBU_CPU_1_RESET_BIT)); return 0; } /***************************************************************************** * A3700 handler called to validate the entry point. ***************************************************************************** */ int a3700_validate_ns_entrypoint(uintptr_t entrypoint) { return PSCI_E_SUCCESS; } /***************************************************************************** * A3700 handler called when a power domain is about to be turned off. The * target_state encodes the power state that each level should transition to. ***************************************************************************** */ void a3700_pwr_domain_off(const psci_power_state_t *target_state) { /* Prevent interrupts from spuriously waking up this cpu */ plat_marvell_gic_cpuif_disable(); /* Core can not be powered down with pending IRQ, * acknowledge all the pending IRQ */ a3700_pm_ack_irq(); } static void a3700_set_gen_pwr_off_option(void) { /* Enable L2 flush -> processor state-machine option */ mmio_setbits_32(MVEBU_PM_NB_CPU_PWR_CTRL_REG, MVEBU_PM_L2_FLUSH_EN); /* * North bridge cannot be VDD off (always ON). * The NB state machine support low power mode by its state machine. * This bit MUST be set for north bridge power down, e.g., * OSC input cutoff(NOT TEST), SRAM power down, PMIC, etc. * It is not related to CPU VDD OFF!! */ mmio_clrbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_CPU_VDDV_OFF_EN); /* * MUST: Switch CPU/AXI clock to OSC * NB state machine clock is always connected to OSC (slow clock). * But Core0/1/processor state machine's clock are connected to AXI * clock. Now, AXI clock takes the TBG as clock source. * If using AXI clock, Core0/1/processor state machine may much faster * than NB state machine. It will cause problem in this case if cores * are released before north bridge gets ready. */ mmio_clrbits_32(MVEBU_NB_CLOCK_SEL_REG, MVEBU_A53_CPU_CLK_SEL); /* * These register bits will trigger north bridge * power-down state machine regardless CM3 status. */ mmio_setbits_32(MVEBU_PM_NB_PWR_DEBUG_REG, MVEBU_PM_IGNORE_CM3_SLEEP); mmio_setbits_32(MVEBU_PM_NB_PWR_DEBUG_REG, MVEBU_PM_IGNORE_CM3_DEEP); /* * SRAM => controlled by north bridge state machine. * Core VDD OFF is not related to CPU SRAM power down. */ mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_NB_SRAM_LKG_PD_EN); /* * Idle AXI interface in order to get L2_WFI * L2 WFI is only asserted after CORE-0 and CORE-1 WFI asserted. * (only both core-0/1in WFI, L2 WFI will be issued by CORE.) * Once L2 WFI asserted, this bit is used for signalling assertion * to AXI IO masters. */ mmio_setbits_32(MVEBU_PM_NB_PWR_CTRL_REG, MVEBU_PM_INTERFACE_IDLE); /* Enable core0 and core1 VDD_OFF */ mmio_setbits_32(MVEBU_PM_CPU_0_PWR_CTRL_REG, MVEBU_PM_CORE_PD); mmio_setbits_32(MVEBU_PM_CPU_1_PWR_CTRL_REG, MVEBU_PM_CORE_PD); /* Enable North bridge power down - * Both Cores MUST enable this bit to power down north bridge! */ mmio_setbits_32(MVEBU_PM_CPU_0_PWR_CTRL_REG, MVEBU_PM_CORE_SOC_PD); mmio_setbits_32(MVEBU_PM_CPU_1_PWR_CTRL_REG, MVEBU_PM_CORE_SOC_PD); /* CA53 (processor domain) power down */ mmio_setbits_32(MVEBU_PM_CPU_0_PWR_CTRL_REG, MVEBU_PM_CORE_PROC_PD); mmio_setbits_32(MVEBU_PM_CPU_1_PWR_CTRL_REG, MVEBU_PM_CORE_PROC_PD); } static void a3700_en_ddr_self_refresh(void) { /* * Both count is 16 bits and configurable. By default, osc stb cnt * is 0xFFF for lower 12 bits. * Thus, powerdown count is smaller than osc count. * This count is used for exiting DDR SR mode on wakeup event. * The powerdown count also has impact on the following * state changes: idle -> count-down -> ... (power-down, vdd off, etc) * Here, make stable counter shorter * Use power down count value instead of osc_stb_cnt to speed up * DDR self refresh exit */ mmio_setbits_32(MVEBU_PM_NB_PWR_CTRL_REG, MVEBU_PM_PWR_DN_CNT_SEL); /* * Enable DDR SR mode => controlled by north bridge state machine * Therefore, we must powerdown north bridge to trigger the DDR SR * mode switching. */ mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_DDR_SR_EN); /* Disable DDR clock, otherwise DDR will not enter into SR mode. */ mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_DDR_CLK_DIS_EN); /* Power down DDR PHY (PAD) */ mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_DDRPHY_PWRDWN_EN); mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_DDRPHY_PAD_PWRDWN_EN); /* Set wait time for DDR ready in ROM code */ mmio_write_32(MVEBU_PM_CPU_VDD_OFF_INFO_1_REG, MVEBU_PM_WAIT_DDR_RDY_VALUE); /* DDR flush write buffer - mandatory */ mmio_write_32(MVEBU_DRAM_CMD_0_REG, MVEBU_DRAM_CH0_CMD0 | MVEBU_DRAM_CS_CMD0 | MVEBU_DRAM_WCB_DRAIN_REQ); while ((mmio_read_32(MVEBU_DRAM_STATS_CH0_REG) & MVEBU_DRAM_WCP_EMPTY) != MVEBU_DRAM_WCP_EMPTY) ; /* Trigger PHY reset after ddr out of self refresh => * supply reset pulse for DDR phy after wake up */ mmio_setbits_32(MVEBU_DRAM_PWR_CTRL_REG, MVEBU_DRAM_PHY_CLK_GATING_EN | MVEBU_DRAM_PHY_AUTO_AC_OFF_EN); } static void a3700_pwr_dn_avs(void) { /* * AVS power down - controlled by north bridge statemachine * Enable AVS power down by clear the AVS disable bit. */ mmio_clrbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_AVS_DISABLE_MODE); /* * Should set BIT[12:13] to powerdown AVS. * 1. Enable AVS VDD2 mode * 2. After power down AVS, we must hold AVS output voltage. * 3. We can choose the lower VDD for AVS power down. */ mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_AVS_VDD2_MODE); mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_AVS_HOLD_MODE); /* Enable low VDD mode, AVS will set CPU to lowest core VDD 747mV */ mmio_setbits_32(MVEBU_AVS_CTRL_2_REG, MVEBU_LOW_VDD_MODE_EN); } static void a3700_pwr_dn_tbg(void) { /* Power down TBG */ mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_TBG_OFF_EN); } static void a3700_pwr_dn_sb(void) { /* Enable south bridge power down option */ mmio_setbits_32(MVEBU_PM_NB_PWR_CTRL_REG, MVEBU_PM_SB_PWR_DWN); /* Enable SDIO_PHY_PWRDWN */ mmio_setbits_32(MVEBU_PM_SB_PWR_OPTION_REG, MVEBU_PM_SDIO_PHY_PDWN_EN); /* Enable SRAM LRM on SB */ mmio_setbits_32(MVEBU_PM_SB_PWR_OPTION_REG, MVEBU_PM_SB_SRAM_LKG_PD_EN); /* Enable SB Power Off */ mmio_setbits_32(MVEBU_PM_SB_PWR_OPTION_REG, MVEBU_PM_SB_VDDV_OFF_EN); /* Kick off South Bridge Power Off */ mmio_setbits_32(MVEBU_PM_SB_CPU_PWR_CTRL_REG, MVEBU_PM_SB_PM_START); } static void a3700_set_pwr_off_option(void) { /* Set general power off option */ a3700_set_gen_pwr_off_option(); /* Enable DDR self refresh in low power mode */ a3700_en_ddr_self_refresh(); /* Power down AVS */ a3700_pwr_dn_avs(); /* Power down TBG */ a3700_pwr_dn_tbg(); /* Power down south bridge, pay attention south bridge setting * should be done before */ a3700_pwr_dn_sb(); } static void a3700_set_wake_up_option(void) { /* * Enable the wakeup event for NB SOC => north-bridge * state-machine enablement on wake-up event */ mmio_setbits_32(MVEBU_PM_NB_WAKE_UP_EN_REG, MVEBU_PM_NB_WKP_EN); /* Enable both core0 and core1 wakeup on demand */ mmio_setbits_32(MVEBU_PM_CPU_WAKE_UP_CONF_REG, MVEBU_PM_CORE1_WAKEUP | MVEBU_PM_CORE0_WAKEUP); /* Enable warm reset in low power mode */ mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_WARM_RESET_EN); } static void a3700_pm_en_nb_gpio(uint32_t gpio) { /* For GPIO1 interrupt -- North bridge only */ if (gpio >= 32) { /* GPIO int mask */ mmio_clrbits_32(MVEBU_NB_GPIO_IRQ_MASK_2_REG, BIT(gpio - 32)); /* NB_CPU_WAKE-up ENABLE GPIO int */ mmio_setbits_32(MVEBU_NB_GPIO_IRQ_EN_HIGH_REG, BIT(gpio - 32)); } else { /* GPIO int mask */ mmio_clrbits_32(MVEBU_NB_GPIO_IRQ_MASK_1_REG, BIT(gpio)); /* NB_CPU_WAKE-up ENABLE GPIO int */ mmio_setbits_32(MVEBU_NB_GPIO_IRQ_EN_LOW_REG, BIT(gpio)); } mmio_setbits_32(MVEBU_NB_STEP_DOWN_INT_EN_REG, MVEBU_NB_GPIO_INT_WAKE_WCPU_CLK); /* Enable using GPIO as wakeup event * (actually not only for north bridge) */ mmio_setbits_32(MVEBU_PM_NB_WAKE_UP_EN_REG, MVEBU_PM_NB_GPIO_WKP_EN | MVEBU_PM_NB_WKP_EN | MVEBU_PM_CORE1_FIQ_IRQ_WKP_EN | MVEBU_PM_CORE0_FIQ_IRQ_WKP_EN); } static void a3700_pm_en_sb_gpio(uint32_t gpio) { /* Enable using GPIO as wakeup event */ mmio_setbits_32(MVEBU_PM_NB_WAKE_UP_EN_REG, MVEBU_PM_SB_WKP_NB_EN | MVEBU_PM_NB_WKP_EN | MVEBU_PM_CORE1_FIQ_IRQ_WKP_EN | MVEBU_PM_CORE0_FIQ_IRQ_WKP_EN); /* SB GPIO Wake UP | South Bridge Wake Up Enable */ mmio_setbits_32(MVEBU_PM_SB_WK_EN_REG, MVEBU_PM_SB_GPIO_WKP_EN | MVEBU_PM_SB_GPIO_WKP_EN); /* GPIO int mask */ mmio_clrbits_32(MVEBU_SB_GPIO_IRQ_MASK_REG, BIT(gpio)); /* NB_CPU_WAKE-up ENABLE GPIO int */ mmio_setbits_32(MVEBU_SB_GPIO_IRQ_EN_REG, BIT(gpio)); } int a3700_pm_src_gpio(union pm_wake_up_src_data *src_data) { if (src_data->gpio_data.bank_num == 0) /* North Bridge GPIO */ a3700_pm_en_nb_gpio(src_data->gpio_data.gpio_num); else a3700_pm_en_sb_gpio(src_data->gpio_data.gpio_num); return 0; } int a3700_pm_src_uart1(union pm_wake_up_src_data *src_data) { /* Clear Uart1 select */ mmio_clrbits_32(MVEBU_NB_GPIO1_SEL_REG, MVEBU_NB_GPIO1_UART1_SEL); /* set pin 19 gpio usage*/ mmio_setbits_32(MVEBU_NB_GPIO1_SEL_REG, MVEBU_NB_GPIO1_GPIO_19_EN); /* Enable gpio wake-up*/ a3700_pm_en_nb_gpio(MVEBU_NB_GPIO_19); /* set pin 18 gpio usage*/ mmio_setbits_32(MVEBU_NB_GPIO1_SEL_REG, MVEBU_NB_GPIO1_GPIO_18_EN); /* Enable gpio wake-up*/ a3700_pm_en_nb_gpio(MVEBU_NB_GPIO_18); return 0; } int a3700_pm_src_uart0(union pm_wake_up_src_data *src_data) { /* set pin 25/26 gpio usage*/ mmio_setbits_32(MVEBU_NB_GPIO1_SEL_REG, MVEBU_NB_GPIO1_GPIO_25_26_EN); /* Enable gpio wake-up*/ a3700_pm_en_nb_gpio(MVEBU_NB_GPIO_25); /* Enable gpio wake-up*/ a3700_pm_en_nb_gpio(MVEBU_NB_GPIO_26); return 0; } struct wake_up_src_func_map src_func_table[WAKE_UP_SRC_MAX] = { {WAKE_UP_SRC_GPIO, a3700_pm_src_gpio}, {WAKE_UP_SRC_UART1, a3700_pm_src_uart1}, {WAKE_UP_SRC_UART0, a3700_pm_src_uart0}, /* FOLLOWING SRC NOT SUPPORTED YET */ {WAKE_UP_SRC_TIMER, NULL} }; static wake_up_src_func a3700_get_wake_up_src_func( enum pm_wake_up_src_type type) { uint32_t loop; for (loop = 0; loop < WAKE_UP_SRC_MAX; loop++) { if (src_func_table[loop].type == type) return src_func_table[loop].func; } return NULL; } #pragma weak mv_wake_up_src_config_get struct pm_wake_up_src_config *mv_wake_up_src_config_get(void) { static struct pm_wake_up_src_config wake_up_src_cfg = {}; return &wake_up_src_cfg; } static void a3700_set_wake_up_source(void) { struct pm_wake_up_src_config *wake_up_src; uint32_t loop; wake_up_src_func src_func = NULL; wake_up_src = mv_wake_up_src_config_get(); for (loop = 0; loop < wake_up_src->wake_up_src_num; loop++) { src_func = a3700_get_wake_up_src_func( wake_up_src->wake_up_src[loop].wake_up_src_type); if (src_func) src_func( &(wake_up_src->wake_up_src[loop].wake_up_data)); } } static void a3700_pm_save_lp_flag(void) { /* Save the flag for enter the low power mode */ mmio_setbits_32(MVEBU_PM_CPU_VDD_OFF_INFO_2_REG, MVEBU_PM_LOW_POWER_STATE); } static void a3700_pm_clear_lp_flag(void) { /* Clear the flag for enter the low power mode */ mmio_clrbits_32(MVEBU_PM_CPU_VDD_OFF_INFO_2_REG, MVEBU_PM_LOW_POWER_STATE); } static uint32_t a3700_pm_get_lp_flag(void) { /* Get the flag for enter the low power mode */ return mmio_read_32(MVEBU_PM_CPU_VDD_OFF_INFO_2_REG) & MVEBU_PM_LOW_POWER_STATE; } /***************************************************************************** * A3700 handler called when a power domain is about to be suspended. The * target_state encodes the power state that each level should transition to. ***************************************************************************** */ void a3700_pwr_domain_suspend(const psci_power_state_t *target_state) { /* Prevent interrupts from spuriously waking up this cpu */ plat_marvell_gic_cpuif_disable(); /* Save IRQ states */ plat_marvell_gic_irq_save(); /* Set wake up options */ a3700_set_wake_up_option(); /* Set wake up sources */ a3700_set_wake_up_source(); /* SoC can not be powered down with pending IRQ, * acknowledge all the pending IRQ */ a3700_pm_ack_irq(); /* Set power off options */ a3700_set_pwr_off_option(); /* Save the flag for enter the low power mode */ a3700_pm_save_lp_flag(); isb(); } /***************************************************************************** * A3700 handler called when a power domain has just been powered on after * being turned off earlier. The target_state encodes the low power state that * each level has woken up from. ***************************************************************************** */ void a3700_pwr_domain_on_finish(const psci_power_state_t *target_state) { /* arch specific configuration */ marvell_psci_arch_init(0); /* Per-CPU interrupt initialization */ plat_marvell_gic_pcpu_init(); plat_marvell_gic_cpuif_enable(); /* Restore the per-cpu IRQ state */ if (a3700_pm_get_lp_flag()) plat_marvell_gic_irq_pcpu_restore(); } /***************************************************************************** * A3700 handler called when a power domain has just been powered on after * having been suspended earlier. The target_state encodes the low power state * that each level has woken up from. * TODO: At the moment we reuse the on finisher and reinitialize the secure * context. Need to implement a separate suspend finisher. ***************************************************************************** */ void a3700_pwr_domain_suspend_finish(const psci_power_state_t *target_state) { struct dec_win_config *io_dec_map; uint32_t dec_win_num; struct dram_win_map dram_wins_map; /* arch specific configuration */ marvell_psci_arch_init(0); /* Interrupt initialization */ plat_marvell_gic_init(); /* Restore IRQ states */ plat_marvell_gic_irq_restore(); /* * Initialize CCI for this cluster after resume from suspend state. * No need for locks as no other CPU is active. */ plat_marvell_interconnect_init(); /* * Enable CCI coherency for the primary CPU's cluster. * Platform specific PSCI code will enable coherency for other * clusters. */ plat_marvell_interconnect_enter_coherency(); /* CPU address decoder windows initialization. */ cpu_wins_init(); /* fetch CPU-DRAM window mapping information by reading * CPU-DRAM decode windows (only the enabled ones) */ dram_win_map_build(&dram_wins_map); /* Get IO address decoder windows */ if (marvell_get_io_dec_win_conf(&io_dec_map, &dec_win_num)) { printf("No IO address decoder windows configurations found!\n"); return; } /* IO address decoder init */ if (init_io_addr_dec(&dram_wins_map, io_dec_map, dec_win_num)) { printf("IO address decoder windows initialization failed!\n"); return; } /* Clear low power mode flag */ a3700_pm_clear_lp_flag(); } /***************************************************************************** * This handler is called by the PSCI implementation during the `SYSTEM_SUSPEND * call to get the `power_state` parameter. This allows the platform to encode * the appropriate State-ID field within the `power_state` parameter which can * be utilized in `pwr_domain_suspend()` to suspend to system affinity level. ***************************************************************************** */ void a3700_get_sys_suspend_power_state(psci_power_state_t *req_state) { /* lower affinities use PLAT_MAX_OFF_STATE */ for (int i = MPIDR_AFFLVL0; i <= PLAT_MAX_PWR_LVL; i++) req_state->pwr_domain_state[i] = PLAT_MAX_OFF_STATE; } /***************************************************************************** * A3700 handlers to shutdown/reboot the system ***************************************************************************** */ static void __dead2 a3700_system_off(void) { ERROR("%s needs to be implemented\n", __func__); panic(); } #pragma weak cm3_system_reset void cm3_system_reset(void) { } /***************************************************************************** * A3700 handlers to reset the system ***************************************************************************** */ static void __dead2 a3700_system_reset(void) { /* Clean the mailbox magic number to let it as act like cold boot */ mmio_write_32(PLAT_MARVELL_MAILBOX_BASE, 0x0); dsbsy(); /* Flush data cache if the mail box shared RAM is cached */ #if PLAT_MARVELL_SHARED_RAM_CACHED flush_dcache_range((uintptr_t)PLAT_MARVELL_MAILBOX_BASE, 2 * sizeof(uint64_t)); #endif /* Use Cortex-M3 secure coprocessor for system reset */ cm3_system_reset(); /* Trigger the warm reset */ mmio_write_32(MVEBU_WARM_RESET_REG, MVEBU_WARM_RESET_MAGIC); /* Shouldn't get to this point */ panic(); } /***************************************************************************** * Export the platform handlers via plat_arm_psci_pm_ops. The ARM Standard * platform layer will take care of registering the handlers with PSCI. ***************************************************************************** */ const plat_psci_ops_t plat_arm_psci_pm_ops = { .cpu_standby = a3700_cpu_standby, .pwr_domain_on = a3700_pwr_domain_on, .pwr_domain_off = a3700_pwr_domain_off, .pwr_domain_suspend = a3700_pwr_domain_suspend, .pwr_domain_on_finish = a3700_pwr_domain_on_finish, .pwr_domain_suspend_finish = a3700_pwr_domain_suspend_finish, .get_sys_suspend_power_state = a3700_get_sys_suspend_power_state, .system_off = a3700_system_off, .system_reset = a3700_system_reset, .validate_power_state = a3700_validate_power_state, .validate_ns_entrypoint = a3700_validate_ns_entrypoint };