openssl/doc/man3/SSL_get_error.pod

=pod

=head1 NAME

SSL_get_error - obtain result code for TLS/SSL I/O operation

=head1 SYNOPSIS

 #include <openssl/ssl.h>

 int SSL_get_error(const SSL *ssl, int ret);

=head1 DESCRIPTION

SSL_get_error() returns a result code (suitable for the C "switch"
statement) for a preceding call to SSL_connect(), SSL_accept(), SSL_do_handshake(),
SSL_read_ex(), SSL_read(), SSL_peek_ex(), SSL_peek(), SSL_write_ex() or
SSL_write() on B<ssl>.  The value returned by that TLS/SSL I/O function must be
passed to SSL_get_error() in parameter B<ret>.

In addition to B<ssl> and B<ret>, SSL_get_error() inspects the
current thread's OpenSSL error queue.  Thus, SSL_get_error() must be
used in the same thread that performed the TLS/SSL I/O operation, and no
other OpenSSL function calls should appear in between.  The current
thread's error queue must be empty before the TLS/SSL I/O operation is
attempted, or SSL_get_error() will not work reliably.

=head1 RETURN VALUES

The following return values can currently occur:

=over 4

=item SSL_ERROR_NONE

The TLS/SSL I/O operation completed.  This result code is returned
if and only if B<ret E<gt> 0>.

=item SSL_ERROR_ZERO_RETURN

The TLS/SSL peer has closed the connection for writing by sending the
close_notify alert.
No more data can be read.
Note that B<SSL_ERROR_ZERO_RETURN> does not necessarily
indicate that the underlying transport has been closed.

=item SSL_ERROR_WANT_READ, SSL_ERROR_WANT_WRITE

The operation did not complete and can be retried later.

B<SSL_ERROR_WANT_READ> is returned when the last operation was a read
operation from a non-blocking B<BIO>.
It means that not enough data was available at this time to complete the
operation.
If at a later time the underlying B<BIO> has data available for reading the same
function can be called again.

SSL_read() and SSL_read_ex() can also set B<SSL_ERROR_WANT_READ> when there is
still unprocessed data available at either the B<SSL> or the B<BIO> layer, even
for a blocking B<BIO>.
See L<SSL_read(3)> for more information.

B<SSL_ERROR_WANT_WRITE> is returned when the last operation was a write
to a non-blocking B<BIO> and it was unable to sent all data to the B<BIO>.
When the B<BIO> is writeable again, the same function can be called again.

Note that the retry may again lead to an B<SSL_ERROR_WANT_READ> or
B<SSL_ERROR_WANT_WRITE> condition.
There is no fixed upper limit for the number of iterations that
may be necessary until progress becomes visible at application
protocol level.

It is safe to call SSL_read() or SSL_read_ex() when more data is available
even when the call that set this error was an SSL_write() or SSL_write_ex().
However if the call was an SSL_write() or SSL_write_ex(), it should be called
again to continue sending the application data.

For socket B<BIO>s (e.g. when SSL_set_fd() was used), select() or
poll() on the underlying socket can be used to find out when the
TLS/SSL I/O function should be retried.

Caveat: Any TLS/SSL I/O function can lead to either of
B<SSL_ERROR_WANT_READ> and B<SSL_ERROR_WANT_WRITE>.
In particular,
SSL_read_ex(), SSL_read(), SSL_peek_ex(), or SSL_peek() may want to write data
and SSL_write() or SSL_write_ex() may want to read data.
This is mainly because
TLS/SSL handshakes may occur at any time during the protocol (initiated by
either the client or the server); SSL_read_ex(), SSL_read(), SSL_peek_ex(),
SSL_peek(), SSL_write_ex(), and SSL_write() will handle any pending handshakes.

=item SSL_ERROR_WANT_CONNECT, SSL_ERROR_WANT_ACCEPT

The operation did not complete; the same TLS/SSL I/O function should be
called again later. The underlying BIO was not connected yet to the peer
and the call would block in connect()/accept(). The SSL function should be
called again when the connection is established. These messages can only
appear with a BIO_s_connect() or BIO_s_accept() BIO, respectively.
In order to find out, when the connection has been successfully established,
on many platforms select() or poll() for writing on the socket file descriptor
can be used.

=item SSL_ERROR_WANT_X509_LOOKUP

The operation did not complete because an application callback set by
SSL_CTX_set_client_cert_cb() has asked to be called again.
The TLS/SSL I/O function should be called again later.
Details depend on the application.

=item SSL_ERROR_WANT_ASYNC

The operation did not complete because an asynchronous engine is still
processing data. This will only occur if the mode has been set to SSL_MODE_ASYNC
using L<SSL_CTX_set_mode(3)> or L<SSL_set_mode(3)> and an asynchronous capable
engine is being used. An application can determine whether the engine has
completed its processing using select() or poll() on the asynchronous wait file
descriptor. This file descriptor is available by calling
L<SSL_get_all_async_fds(3)> or L<SSL_get_changed_async_fds(3)>. The TLS/SSL I/O
function should be called again later. The function B<must> be called from the
same thread that the original call was made from.

=item SSL_ERROR_WANT_ASYNC_JOB

The asynchronous job could not be started because there were no async jobs
available in the pool (see ASYNC_init_thread(3)). This will only occur if the
mode has been set to SSL_MODE_ASYNC using L<SSL_CTX_set_mode(3)> or
L<SSL_set_mode(3)> and a maximum limit has been set on the async job pool
through a call to L<ASYNC_init_thread(3)>. The application should retry the
operation after a currently executing asynchronous operation for the current
thread has completed.

=item SSL_ERROR_WANT_CLIENT_HELLO_CB

The operation did not complete because an application callback set by
SSL_CTX_set_client_hello_cb() has asked to be called again.
The TLS/SSL I/O function should be called again later.
Details depend on the application.

=item SSL_ERROR_SYSCALL

Some non-recoverable I/O error occurred.
The OpenSSL error queue may contain more information on the error.
For socket I/O on Unix systems, consult B<errno> for details.

This value can also be returned for other errors, check the error queue for
details.

=item SSL_ERROR_SSL

A failure in the SSL library occurred, usually a protocol error.  The
OpenSSL error queue contains more information on the error.

=back

=head1 SEE ALSO

L<ssl(7)>

=head1 HISTORY

The SSL_ERROR_WANT_ASYNC error code was added in OpenSSL 1.1.0.
The SSL_ERROR_WANT_CLIENT_HELLO_CB error code was added in OpenSSL 1.1.1.

=head1 COPYRIGHT

Copyright 2000-2018 The OpenSSL Project Authors. All Rights Reserved.

Licensed under the Apache License 2.0 (the "License").  You may not use
this file except in compliance with the License.  You can obtain a copy
in the file LICENSE in the source distribution or at
L<https://www.openssl.org/source/license.html>.

=cut