/* * Definitions for IO devices. Used only in C. */ enum { /* hardware counter frequency */ ClockFreq= 3686400, }; /* * IRQ's defined by SA1100 */ enum { IRQgpio0= 0, IRQgpio1= 1, IRQgpio2= 2, IRQgpio3= 3, IRQgpio4= 4, IRQgpio5= 5, IRQgpio6= 6, IRQgpio7= 7, IRQgpio8= 8, IRQgpio9= 9, IRQgpio10= 10, IRQgpiohi= 11, IRQlcd= 12, IRQudc= 13, IRQuart1b= 15, IRQuart2= 16, IRQuart3= 17, IRQmcp= 18, IRQssp= 19, IRQdma0= 20, IRQdma1= 21, IRQdma2= 22, IRQdma3= 23, IRQdma4= 24, IRQdma5= 25, IRQtimer0= 26, IRQtimer1= 27, IRQtimer2= 28, IRQtimer3= 29, IRQsecond= 30, IRQrtc= 31, }; /* * GPIO lines (signal names from compaq document). _i indicates input * and _o output. */ enum { GPIO_PWR_ON_i= 1<<0, /* power button */ GPIO_UP_IRQ_i= 1<<1, /* microcontroller interrupts */ GPIO_LDD8_o= 1<<2, /* LCD data 8-15 */ GPIO_LDD9_o= 1<<3, GPIO_LDD10_o= 1<<4, GPIO_LDD11_o= 1<<5, GPIO_LDD12_o= 1<<6, GPIO_LDD13_o= 1<<7, GPIO_LDD14_o= 1<<8, GPIO_LDD15_o= 1<<9, GPIO_CARD_IND1_i= 1<<10, /* card inserted in PCMCIA socket 1 */ GPIO_CARD_IRQ1_i= 1<<11, /* PCMCIA socket 1 interrupt */ GPIO_CLK_SET0_o= 1<<12, /* clock selects for audio codec */ GPIO_CLK_SET1_o= 1<<13, GPIO_L3_SDA_io= 1<<14, /* UDA1341 interface */ GPIO_L3_MODE_o= 1<<15, GPIO_L3_SCLK_o= 1<<16, GPIO_CARD_IND0_i= 1<<17, /* card inserted in PCMCIA socket 0 */ GPIO_KEY_ACT_i= 1<<18, /* hot key from cradle */ GPIO_SYS_CLK_i= 1<<19, /* clock from codec */ GPIO_BAT_FAULT_i= 1<<20, /* battery fault */ GPIO_CARD_IRQ0_i= 1<<21, /* PCMCIA socket 0 interrupt */ GPIO_LOCK_i= 1<<22, /* expansion pack lock/unlock */ GPIO_COM_DCD_i= 1<<23, /* DCD from UART3 */ GPIO_OPT_IRQ_i= 1<<24, /* expansion pack IRQ */ GPIO_COM_CTS_i= 1<<25, /* CTS from UART3 */ GPIO_COM_RTS_o= 1<<26, /* RTS to UART3 */ GPIO_OPT_IND_i= 1<<27, /* expansion pack inserted */ /* Peripheral Unit GPIO pin assignments: alternate functions */ GPIO_SSP_TXD_o= 1<<10, /* SSP Transmit Data */ GPIO_SSP_RXD_i= 1<<11, /* SSP Receive Data */ GPIO_SSP_SCLK_o= 1<<12, /* SSP Sample CLocK */ GPIO_SSP_SFRM_o= 1<<13, /* SSP Sample FRaMe */ /* ser. port 1: */ GPIO_UART_TXD_o= 1<<14, /* UART Transmit Data */ GPIO_UART_RXD_i= 1<<15, /* UART Receive Data */ GPIO_SDLC_SCLK_io= 1<<16, /* SDLC Sample CLocK (I/O) */ GPIO_SDLC_AAF_o= 1<<17, /* SDLC Abort After Frame */ GPIO_UART_SCLK1_i= 1<<18, /* UART Sample CLocK 1 */ /* ser. port 4: */ GPIO_SSP_CLK_i= 1<<19, /* SSP external CLocK */ /* ser. port 3: */ GPIO_UART_SCLK3_i= 1<<20, /* UART Sample CLocK 3 */ /* ser. port 4: */ GPIO_MCP_CLK_i= 1<<21, /* MCP CLocK */ /* test controller: */ GPIO_TIC_ACK_o= 1<<21, /* TIC ACKnowledge */ GPIO_MBGNT_o= 1<<21, /* Memory Bus GraNT */ GPIO_TREQA_i= 1<<22, /* TIC REQuest A */ GPIO_MBREQ_i= 1<<22, /* Memory Bus REQuest */ GPIO_TREQB_i= 1<<23, /* TIC REQuest B */ GPIO_1Hz_o= 1<<25, /* 1 Hz clock */ GPIO_RCLK_o= 1<<26, /* internal (R) CLocK (O, fcpu/2) */ GPIO_32_768kHz_o= 1<<27, /* 32.768 kHz clock (O, RTC) */ }; /* * types of interrupts */ enum { GPIOrising, GPIOfalling, GPIOboth, IRQ, }; /* hardware registers */ typedef struct Uartregs Uartregs; struct Uartregs { ulong ctl[4]; ulong dummya; ulong data; ulong dummyb; ulong status[2]; }; Uartregs *uart3regs; /* general purpose I/O lines control registers */ typedef struct GPIOregs GPIOregs; struct GPIOregs { ulong level; /* 1 == high */ ulong direction; /* 1 == output */ ulong set; /* a 1 sets the bit, 0 leaves it alone */ ulong clear; /* a 1 clears the bit, 0 leaves it alone */ ulong rising; /* rising edge detect enable */ ulong falling; /* falling edge detect enable */ ulong edgestatus; /* writing a 1 bit clears */ ulong altfunc; /* turn on alternate function for any set bits */ }; extern GPIOregs *gpioregs; /* extra general purpose I/O bits, output only */ enum { EGPIO_prog_flash= 1<<0, EGPIO_pcmcia_reset= 1<<1, EGPIO_exppack_reset= 1<<2, EGPIO_codec_reset= 1<<3, EGPIO_exp_nvram_power= 1<<4, EGPIO_exp_full_power= 1<<5, EGPIO_lcd_3v= 1<<6, EGPIO_rs232_power= 1<<7, EGPIO_lcd_ic_power= 1<<8, EGPIO_ir_power= 1<<9, EGPIO_audio_power= 1<<10, EGPIO_audio_ic_power= 1<<11, EGPIO_audio_mute= 1<<12, EGPIO_fir= 1<<13, /* not set is sir */ EGPIO_lcd_5v= 1<<14, EGPIO_lcd_9v= 1<<15, }; extern ulong *egpioreg; /* Peripheral pin controller registers */ typedef struct PPCregs PPCregs; struct PPCregs { ulong direction; ulong state; ulong assignment; ulong sleepdir; ulong flags; }; extern PPCregs *ppcregs; /* Synchronous Serial Port controller registers */ typedef struct SSPregs SSPregs; struct SSPregs { ulong control0; ulong control1; ulong dummy0; ulong data; ulong dummy1; ulong status; }; extern SSPregs *sspregs; /* Multimedia Communications Port controller registers */ typedef struct MCPregs MCPregs; struct MCPregs { ulong control0; ulong reserved0; ulong data0; ulong data1; ulong data2; ulong reserved1; ulong status; ulong reserved[11]; ulong control1; }; extern MCPregs *mcpregs; /* * memory configuration */ enum { /* bit shifts for pcmcia access time counters */ MECR_io0= 0, MECR_attr0= 5, MECR_mem0= 10, MECR_fast0= 11, MECR_io1= MECR_io0+16, MECR_attr1= MECR_attr0+16, MECR_mem1= MECR_mem0+16, MECR_fast1= MECR_fast0+16, }; typedef struct MemConfRegs MemConfRegs; struct MemConfRegs { ulong mdcnfg; /* dram */ ulong mdcas00; /* dram banks 0/1 */ ulong mdcas01; ulong mdcas02; ulong msc0; /* static */ ulong msc1; ulong mecr; /* pcmcia */ ulong mdrefr; /* dram refresh */ ulong mdcas20; /* dram banks 2/3 */ ulong mdcas21; ulong mdcas22; ulong msc2; /* static */ ulong smcnfg; /* SMROM config */ }; extern MemConfRegs *memconfregs; /* * power management */ typedef struct PowerRegs PowerRegs; struct PowerRegs { ulong pmcr; /* Power manager control register */ ulong pssr; /* Power manager sleep status register */ ulong pspr; /* Power manager scratch pad register */ ulong pwer; /* Power manager wakeup enable register */ ulong pcfr; /* Power manager general configuration register */ ulong ppcr; /* Power manager PPL configuration register */ ulong pgsr; /* Power manager GPIO sleep state register */ ulong posr; /* Power manager oscillator status register */ }; extern PowerRegs *powerregs;