1
0

kn.dts 2.0 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124
  1. /dts-v1/;
  2. #include "rt3050.dtsi"
  3. #include <dt-bindings/gpio/gpio.h>
  4. #include <dt-bindings/input/input.h>
  5. / {
  6. compatible = "zyxel,keenetic", "ralink,rt3052-soc";
  7. model = "ZyXEL Keenetic";
  8. aliases {
  9. led-boot = &led_power;
  10. led-failsafe = &led_power;
  11. led-running = &led_power;
  12. led-upgrade = &led_power;
  13. };
  14. cfi@1f000000 {
  15. compatible = "cfi-flash";
  16. reg = <0x1f000000 0x800000>;
  17. bank-width = <2>;
  18. device-width = <2>;
  19. partitions {
  20. compatible = "fixed-partitions";
  21. #address-cells = <1>;
  22. #size-cells = <1>;
  23. partition@0 {
  24. label = "u-boot";
  25. reg = <0x0 0x30000>;
  26. read-only;
  27. };
  28. partition@30000 {
  29. label = "u-boot-env";
  30. reg = <0x30000 0x10000>;
  31. read-only;
  32. };
  33. factory: partition@40000 {
  34. label = "factory";
  35. reg = <0x40000 0x10000>;
  36. read-only;
  37. };
  38. partition@50000 {
  39. label = "firmware";
  40. reg = <0x50000 0x3b0000>;
  41. };
  42. };
  43. };
  44. gpio-leds {
  45. compatible = "gpio-leds";
  46. led_power: power {
  47. label = "kn:green:power";
  48. gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  49. };
  50. usb {
  51. label = "kn:green:usb";
  52. gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
  53. trigger-sources = <&otg_port1>;
  54. linux,default-trigger = "usbport";
  55. };
  56. wps {
  57. label = "kn:green:wps";
  58. gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
  59. };
  60. };
  61. gpio-keys-polled {
  62. compatible = "gpio-keys-polled";
  63. poll-interval = <20>;
  64. reset {
  65. label = "reset";
  66. gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
  67. linux,code = <KEY_RESTART>;
  68. };
  69. rfkill {
  70. label = "rfkill";
  71. gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
  72. linux,code = <KEY_RFKILL>;
  73. linux,input-type = <EV_SW>;
  74. };
  75. wps {
  76. label = "wps";
  77. gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
  78. linux,code = <KEY_WPS_BUTTON>;
  79. };
  80. };
  81. };
  82. &pinctrl {
  83. state_default: pinctrl0 {
  84. gpio {
  85. ralink,group = "uartf";
  86. ralink,function = "gpio";
  87. };
  88. };
  89. };
  90. &ethernet {
  91. mtd-mac-address = <&factory 0x28>;
  92. };
  93. &esw {
  94. mediatek,portmap = <0x2f>;
  95. };
  96. &wmac {
  97. ralink,mtd-eeprom = <&factory 0>;
  98. };
  99. &otg {
  100. status = "okay";
  101. };